ML BOATWORKS Radio Controlled Race Boat Designs

1/8th Scale Newton 147/ MHR 8501 Kit

This kit makes the following boats and possibly more that are not listed. The 100 series number matches the Newton Marine numbering. The 4 digit number matches the NAMBA Master Hull Roster. 1) 147-A, 8501, '85 Bubble Budweiser U-12 2) 147-B, 8501, ’91 Miss Ginger Honey U-89     ***PLEASE NOTE- UNLESS STATED HERE, THIS ML BOATWORKS SCALE HYDROPLANE KITS ONLY INCLUDE THE INTERNAL PLYWOOD FRAMING. BASSWOOD STICKS AND PLYWOOD SHEETING ARE REQUIRED. THOSE REQUIREMENTS ARE LISTED BELOW*** Chances are, you have heard about the quality of the ML Boatworks scale hydroplane kits. For the last few years, we have helped re-open the door for wood boat builders. These kits are made from top quality birch plywood and with the use of CAD, have excellent fitment. ML Boatworks Scale Hydroplane kits fit the general scale hydroplane rules for both NAMBA and IMPBA. We do modify "below the water line" ride surfaces to maximize hull efficiency and stability. Please see the NAMBA Master Hull Roster for all boats this kit makes. Paint and Sheeting Sheets for this kit are available at www.newtonmarine.com. Newton Marine plan sheets are to be considered the instruction manual for these kits, however all of our kits have a laser etched number system that helps the builder match up all the framework. ML Boatworks works very close with Newton Marine, and we try to keep the frame numbering system close to their plan sheets. If you are an inexperienced builder, PLEASE contact ML Boatworks before ordering so we can guide you towards a kit that matches your experience level. Length: Most all 1/8th scale kits are between 42-47". Designed to run in a CLOCKWISE direction only. ML Boatworks scale kits FIT THE MASTER HULL ROSTER! Hardware/Fiberglass/Wood Parts Recommended: *Speedmaster or Accu-tech 60/90 rudder, single pickup for nitro, Dual Pickup for FE, 1-5/8" bearing block *Speedmaster or Accu-tech 1/4" flat bottom hydroplane Strut (Modern Hulls may use the "Extended" style Strut) *Speedmaster or Accu-tech 1/4" flex cable with 1/4" to 3/16" prop shaft *Virginia Craftsman ( [email protected] ) or http://accu-techrchardware.com/ 1/8th Scale Turn Fin *www.rcboatcompany.com for cowling, rear wing, turbine tube, canards, stabilizer bar kits for rear wings *For 1/8th scale kits, (5) sheets of 1/16" x 12" x 48" Birch Plywood are generally required. Available in the Accessories section. *For this kit, 3/16"x 3/16"x 48" Basswood Sticks are required. (2) bundles of 10 sticks are recommended. Available in the Accessories section.  

1/10th Scale Newton 146 MHR 8401, 8700 - Lucero Sponsons Kit

This kit makes the following boats and possibly more that are not listed. The 100 series number matches the Newton Marine numbering. The 4 digit number matches the NAMBA Master Hull Roster.    1) 146-A, 8401, '84 Atlas Van Lines U-1 (available offset or centered engine well) 2) 146-B, 8401, ’85 Miller American U-00 (available offset or centered engine well) 3) 146-C, 8401,’88 Miller High Life U-00 (available offset or centered engine well) 4) 146-D, 8700, '87 Miller American U-00 "Star Wars canopy" (available offset or centered engine well) 5) 146-E, 8401, ‘88 Miss Circus Circus U-00 (available offset or centered engine well) 6) 146-F, 8700, ‘88 Miller High Life U-31 (available offset or centered engine well) 5) 146-G, 8700, ‘88 Miss Circus Circus U-31 (available offset or centered engine well)     ***PLEASE NOTE- UNLESS STATED HERE, THIS ML BOATWORKS SCALE HYDROPLANE KITS ONLY INCLUDE THE INTERNAL PLYWOOD FRAMING. BASSWOOD STICKS AND PLYWOOD SHEETING ARE REQUIRED. THOSE REQUIREMENTS ARE LISTED BELOW*** Chances are, you have heard about the quality of the ML Boatworks scale hydroplane kits. For the last few years, we have helped re-open the door for wood boat builders. These kits are made from top quality birch plywood and with the use of CAD, have excellent fitment. ML Boatworks Scale Hydroplane kits fit the general scale hydroplane rules for both NAMBA and IMPBA. We do modify "below the water line" ride surfaces to maximize hull efficiency and stability. Please see the NAMBA Master Hull Roster for all boats this kit makes. While only available as 1/8th scale plans, paint and sheeting sheets for this kit are available at www.newtonmarine.com. Newton Marine plan sheets are to be considered the instruction manual for these kits, however all of our kits have a laser etched number system that helps the builder match up all the framework. You will want to take the Newton Marine plans and have them scaled down to 80% of their original size to closely match the 1/10th scale size! ML Boatworks works very close with Newton Marine, and we try to keep the frame numbering system close to their plan sheets. If you are an inexperienced builder, PLEASE contact ML Boatworks before ordering so we can guide you towards a kit that matches your experience level. Length: Most all 1/10th scale kits are between 34-37". ML Boatworks scale kits FIT THE MASTER HULL ROSTER! Hardware/Fiberglass/Wood Parts Recommended: *Speedmaster or Accu-tech 20 rudder *Speedmaster or Accu-tech 3/16" flat bottom hydroplane Strut (Modern Hulls may use the "Extended" style Strut) *Speedmaster or Accu-tech 3/16" flex cable and prop shaft *Virginia Craftsman ( [email protected] ) or http://accu-techrchardware.com/ 1/10th Scale or Sport 20 or 40 Turn Fin *www.hydroscalecreations.us for cowling, rear wing, turbine tube, canards, stabilizer bar kits for rear wings *For 1/10th scale kits, (3) sheets of 1/16" x 12" x 48" Birch Plywood are generally required. Available in the Accessories section. *For this kit, 3/16"x 3/16"x 48" Basswood Sticks are required. (2) bundles of 10 sticks are recommended. Available in the Accessories section.